Almost everyone seems to have their private thinking about Installing A Bathtub.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging task. If the old bathtub is readily available, the task can relocate quickly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have certified on your own for the work as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly help you install a new bathtub in your bathroom if you have already purchased a new tub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list must make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the bathtub until the spirit level reads level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and check all joints and new pipework for leaks as well as tighten them if required. Fill up the tub as well as likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the tub has been used at least once as this will settle it right into its last placement.
Planning for the Setup
First of all, the supporting framework supplied with the bath should be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the activity experienced when the tub is in usage. The sealant can break rather early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very involved in Tools You Need to Install a New Bathtub and I hope you enjoyed the post. So long as you enjoyed reading our page kindly make sure you remember to pass it around. Thank you for your time spent reading it.
Additional Information